Clear PVC Tubing 3/8" ID 1/2" OD - 100ft for Aquariums & Plumbing

This worked out fine for me. The sizing was accurate, and I was able to use it as insulation to aid protection of old BX electrical wires. (They are rayon covered, and 70 years old, so where they exit the BX steel protective covering, the original insulation is not 100% to be relied upon. So in the load center, I was able to improve their safety.)I used this tubing to protect the filament on my 3D printer. It is the perfect size for use with 1.75mm diameter filament and is way cheaper than the PTFE that most people use. The only difference between this and the PTFE is that this is less rigid which ultimately means it is more flexible and better for ninjaflex. However, most filaments (I primarily use PLA) are quite rigid and will hold up this tubing and prevent it from contorting.I have only used this tubing as a shielding for 3D printer filament and it works beautifully for that purpose. I cannot comment on how it works for fluid flow or other applications.I highly recommend this for 3D printing applications and will likely get more once I run out. The only downside is that it is slightly tacky and might not be good for long runs of filament. I use primarily 1ft sections and it works well for that.I should have compared the dimensions to the image, as one of the two images on the website is misleading. The provided dimensions are correct. The first image to pop up is not an image of the described product. However, the image below the one which is the first to pop up, i.e. the image of the entire coil, is in fact likely an accurate image.It arrived without kinks. It's extremely clear, and extremely flexible. It's the size it says it is, and it's just as cheap as buying it at a local giant lumber yard. It does arrive with some memory from being coiled, so I put the tennis shoe rack in the dryer, left it in a coil, and heated it up. After a few minutes, I laid it out, let it cool, and it stayed straight. I'm using it to make some custom LED outdoor lighting strips, and so far, it's working out great. It's solid, but not so heavy that's it's not flexible.used it for a one man brake bleeding setup (just some tube and an old bottle) and this fit the bill perfectly. probably way too thick for what i needed but hey it was cheap and i know it will be durable as brake fluid is super corrosive. the only downside i have to say is that when the bottle was empty the tube was so heavy it was causing it to fall over but once it filled up a little bit there were no problems, however i cant really take off stars for heavy duty tube being too heavy for an empty bottle.Good product, 4 stars because it took forever to get here and it was packaged with very annoying clear tape that took me a while to get off, still sticky in some areas. Beside that it's perfectDimensions were accurate but I received braided hose and not clear. Braided will work so I did not return but I was expecting clear.My air conditioner is in my attic where there is no sewage line close to the unit. The AC guys uran PVC pipe to drain the unit but it leaked 3 times in 3 different places so I finally gave up on that plan. I attached this tubing to the water pump instead and it works perfectly...no joints so no leaks. It is high quality and cost me probably less than half of what a local hardware store (even the big box stores) wanted for this tubing!!! What a great bargain, thanks!!!Arrived twisted and kinked - it would have taken an extra 30 seconds to make sure the twists were out of the tubing before clinching down the zip tie. I needed the tubing and through 90 min of heat and stretching I got 12 ft of tubing out of it that is usable. The rest went in the trash.The piece I ordered was kinked so badly is was worthless. Hopefully the replacement will be better. The piece I received appeared to be a cutoff that may have been rejected by somebody else that makes or uses mass quantities of this stuff. I won't hold my breath waiting for a perfectly unkinked piece just as long as i can get a decent length out of it...Perfect size ID send OD. Glad it's food grade.I use it to attach my pure RO filtered water tap and draw water into my espresso machine 7ft away. Don't ask why I need it setup like this.... Long story;)I tried but cannot find any fault with this product. It is what it said it was.Clear plastic tubing that will flex and bend.Wall is a bit thin for most of my 1/4 in tubing connectors that are supposed to work on 1/4 in id tubing...leaks.